Category: BCNet

Siemens PLC with HMI for data point table detection

~ arcozhang ~ Leave a comment

This example is based on the hardware S7 bus analysis function of BCNet-S7200-S or BCNet-S7300-S to realize the detection of touch screen data points and analyze the important point table information of current PLC in combination with the panel information of touch screen. BCNet-S7300-S is used for Siemens S7-200, SMART S7-200, S7-300, S7-400 series PLC Ethernet data acquisition, … Continue reading Siemens PLC with HMI for data point table detection

BCNet-S7200Plus and SMART200 PLC data exchange

~ arcozhang ~ Leave a comment

This example takes S7-200 (CPU224XP) and SMART200 as an example to introduce how to exchange data between them. The DB9 male port (X1) of BCNet is connected to the PPI port of S7-200, and the Ethernet port of SMART200 comes with BCNet is connected to the BCNet-S7200Plus through a switch. BCNet configures the exchange command through BCDevice … Continue reading BCNet-S7200Plus and SMART200 PLC data exchange

Data exchange between S7300 and Siemens PLCs such as S7-1200/1500 via BCNet

~ arcozhang ~ Leave a comment

The BCNet communication module enables Ethernet communication between PLCs such as S7300 and S7200 and PLCs such as S7-1200, S7-1500 and S7200 Smart through simple command configuration. This example takes S7-1200 and S7-300 as an example, and S7-1500 and SMART 200 follow similar steps. Hardware Connection DB9 serial port of BCNet-S7300Plus connects to the MPI port/DP port … Continue reading Data exchange between S7300 and Siemens PLCs such as S7-1200/1500 via BCNet

Schneider Quantum PLC communicates with Siemens S7300

~ arcozhang ~ Leave a comment

Schneider Quantum PLC needs to communicate with Siemens S7300, S7200 and other PLCs. In this paper, we implement modbusTCP communication connection between Siemens S7300 PLC (PROFINET) and Schneider Quantum PLC through BCNet-S7300Plus series gateway. Siemens PLC parameter settings 1,Siemens S7300 configured for MPI or PROFIBUS communication, set the MPI/DP station address of the PLC: default is 2.2,PLC … Continue reading Schneider Quantum PLC communicates with Siemens S7300

Siemens S7300 and S7200 with IFIX Ethernet communication via BCNet-S7

~ arcozhang ~ Leave a comment

BCNet-S7MPI connects to Siemens S7300 PLC; BCNet-S7PPI connects to Siemens S7200 PLC; in IFIX software, the communication method of S7TCP/IP driven by S7A is used. Take the S7 TCP driver (S7A) connected to one S7300 and one S7200 as an example Set the parameters of BCNet-S7 module Using Siemens S7TCP driver to communicate, you need … Continue reading Siemens S7300 and S7200 with IFIX Ethernet communication via BCNet-S7

BCNet Implementation of Mitsubishi FX and HMI Data Point Table Detection

~ arcozhang ~ Leave a comment

This example is based on the PLC bus protocol analysis function of BCNet-FX-S to realize the detection of HMI touch screen data points and analyze the current PLC important point table information in combination with the touch screen panel information. BCNet-FX-S is used for Mitsubishi FX1S/1N/2N/3S/3G/3GA/3GC/3U/3UC series, Huichuan, Shihlin AX, Hogawa and other PLC Ethernet data … Continue reading BCNet Implementation of Mitsubishi FX and HMI Data Point Table Detection

Mitsubishi PLC Ethernet Program Upload Download

~ arcozhang ~ Leave a comment

BCNet-FX supports Mitsubishi programming software GX Works2 for program uploading and monitoring of the full range of FX PLCs via Ethernet, and with the remote module, program maintenance and data acquisition of remote devices can be conveniently realized. Mode 1: For FX3G/3GC, FX3S, FX3U/3UC This method is applicable to FX3G/3GC, FX3S, FX3U/FX3UC, which are 3 series … Continue reading Mitsubishi PLC Ethernet Program Upload Download

Mitsubishi FX3U connects to MX Component via BCNet-FX

~ arcozhang ~ Leave a comment

The setup process is as follows. Run the Communication Setup Utility. Click “Wizard”, configure a connection, fill in “Logical station number”, e.g. 0, and click “Next”. Select “Ethernet board” for “PC side I/F” and “Connect module” for Select “FX3U-ENET-ADP” and click “Next”. Click “Find CPU (Built-in Ethernet port) on network”, find the BCNet-FX in the … Continue reading Mitsubishi FX3U connects to MX Component via BCNet-FX

ModbusTCP communication of Mitsubishi Q series PLC

~ arcozhang ~ Leave a comment

BCNet-Q is a new Ethernet communication processor designed to meet the increasing demand for plant equipment informatization (equipment network monitoring and production management) for Ethernet data acquisition from Mitsubishi Q0x/Q0xU/Q0xUD series PLCs, BCNet-Q supports most SCADA software in the industrial control field, and supports both Mitsubishi Ethernet protocol and BCNet-Q supports most SCADA software in the … Continue reading ModbusTCP communication of Mitsubishi Q series PLC

Modbus TCP communication of Mitsubishi FX series PLC

~ arcozhang ~ Leave a comment

BCNet-FX is a new type of Ethernet communication processor, designed to meet the increasing informatization requirements of factory equipment (equipment network monitoring and production management). It is used in Mitsubishi FX1S/1N/2N/3S/3G/3GC /3U/3UC series PLC Ethernet data acquisition, BCNet-FX supports most SCADA software in the field of industrial control, supports Mitsubishi Ethernet protocol and ModbusTCP two communication … Continue reading Modbus TCP communication of Mitsubishi FX series PLC